pinouts

Centronics printer connector

pinout (распиновка)

запомнить адрес в закладки

One of the most used printer interfaces, since every Intel/DOS/Windows based Personal Computer today has a Sub-D25 female connector which is called LPT1, printer-side connector

разъем 36 pin CENTRONICS FEMALE
36 pin CENTRONICS FEMALE connector  at the printer
Pin Name Dir Description
1 /STROBE <-- Strobe
2 D0 <-> Data Bit 0
3 D1 <-> Data Bit 1
4 D2 <-> Data Bit 2
5 D3 <-> Data Bit 3
6 D4 <-> Data Bit 4
7 D5 <-> Data Bit 5
8 D6 <-> Data Bit 6
9 D7 <-> Data Bit 7
10 /ACK --> Acknowledge
11 BUSY --> Busy
12 POUT --> Paper Out
13 SEL --> Select
14 /AUTOFEED <-- Autofeed
15 n/c - Not used
16 0 V --- Logic Ground
17 CHASSIS GND --- Shield Ground
18 +5 V PULLUP --> +5 V DC (50 mA max)
19 GND --- Signal Ground (Strobe Ground)
20 GND --- Signal Ground (Data 0 Ground)
21 GND --- Signal Ground (Data 1 Ground)
22 GND --- Signal Ground (Data 2 Ground)
23 GND --- Signal Ground (Data 3 Ground)
24 GND --- Signal Ground (Data 4 Ground)
25 GND --- Signal Ground (Data 5 Ground)
26 GND --- Signal Ground (Data 6 Ground)
27 GND --- Signal Ground (Data 7 Ground)
28 GND --- Signal Ground (Acknowledge Ground)
29 GND --- Signal Ground (Busy Ground)
30 /GNDRESET --- Reset Ground
31 /RESET <-- Reset
32 /FAULT --> Fault (Low when offline)
33 0 V --- Signal Ground
34 n/c - Not used
35 +5 V --> +5 V DC
36 /SLCT IN <-- Select In (Taking low or high sets printer on line or off line respectively)
Functional Description
STROBE:Active low pulse used to transfer data into the printer.Pulse with must be between 0.5 and 500 microseconds for most printers.
Dn:Data lines, high is a one. 
ACK:Active low pulse indicates that data has been received and the printer is ready to accept more. 
BUSY:A high signal indicates that the printer cannot receive data. 
PE:A high signal indicates that the printer is out of paper (Paper End) 
SELECT OUT:A high signal indicates that the printer is on-line 
AUTO FEED:A low signal indicates to the printer that a line feed is required after each Carriage return.This signal is used as a ground line by some manufacturers.
OSCXT:A 100-200 KHz signal used by true Centronics printers only. 
+5V:+5VdcNot provided by all manufacturers
PRIME:A low signal resets the printer to its power-up state and the printer buffer is cleared 
FAULT:A low signal indicates that the printer is in an off-line or error state 
LINE COUNT:Used by true Centronics printers only.Most of the time not used
SELECT IN:A high signal indicates to the printer that a DC1/ DC3 code is valid.This signal is used by a few manufacturers

Note: Direction is Printer relative Computer.

Эта информация должна быть правильной, но ошибки вполне возможны. Вы можете помочь!
Вы можете подтвердить правильность документа (только если действительно уверены), или сообщить об ошибке в документе (ошибка может быть описана далее по ссылке). Ваше мнение будет учтено при расчете статуса документа.
Ссылки по теме:
Pinouts.ru > Распиновки параллельных портов >  Распиновка Centronics printer connector использующего разъем 36 pin CENTRONICS FEMALE

Источник(и): Connectivity Knowledge Platform (Made IT), from Hardware Book, Peter Korsgaard, Petr Krc
Статус документа: не подтвержденный
отметить как ошибочный!
отметить как правильный
0 отзыв(ов)
Щелкните по одной из ссылок для изменения статуса документа.
[Обсудить на форуме] [Назад к оглавлению] [Добавить распайку]
[Сообщить об ошибке или обновлении]
Maintained by pinouts.ru team
This information is provided as a guideline only.
Efforts have been made to ensure it is correct, but it is the responsibility of the user
to verify the data is correct for their application
107 hits since February 11, 2005