Pinouts of Connectors

PC/104 bus pinout

layout
schematic diagram

add this page to bookmarks

PC/104 is a compact version of the ISA bus, optimized for the requirements of embedded systems

146 pin PC/104 16 bit connector pin-out & layout
146 pin PC/104 16 bit connector
Differences from ISA are:
  • Reduced form-factor to 90 by 96 mm.
  • Eliminated the need for backplanes or card cages, through its self-stacking bus
  • Minimized component count and power consumption (to typically 1-2 Watts per module), by reducing required bus drive on most signals to 4 mA.

PC/104 modules can be of two bus types, 8-bit and 16-bit. These correspond to the PC and PC/AT buses, respectively.

Pin J1/P1 J1/P1 J2/P2 (16-bit modules only) J2/P2 (16-bit modules only)
Number Row A Row B Row C1 Row D1
0 -- -- 0V 0V
1 IOCHCHK* 0V SBHE* MEMCS16*
2 SD7 RESETDRV LA23 IOCS16*
3 SD6 +5V LA22 IRQ10
4 SD5 IRQ9 LA21 IRQ11
5 SD4 -5V LA20 IRQ12
6 SD3 DRQ2 LA19 IRQ15
7 SD2 -12V LA18 IRQ14
8 SD1 ENDXFR* LA17 DACK0*
9 SD0 +12V MEMR* DRQ0
10 IOCHRDY (KEY)2 MEMW* DACK5*
11 AEN SMEMW* SD8 DRQ5
12 SA19 SMEMR* SD9 DACK6*
13 SA18 IOW* SD10 DRQ6
14 SA17 IOR* SD11 DACK7*
15 SA16 DACK3* SD12 DRQ7
16 SA15 DRQ3 SD13 +5V
17 SA14 DACK1* SD14 MASTER*
18 SA13 DRQ1 SD15 0V
19 SA12 REFRESH* (KEY)2 0V
20 SA11 SYSCLK -- --
21 SA10 IRQ7 -- --
22 SA9 IRQ6 -- --
23 SA8 IRQ5 -- --
24 SA7 IRQ4 -- --
25 SA6 IRQ3 -- --
26 SA5 DACK2* -- --
27 SA4 TC -- --
28 SA3 BALE -- --
29 SA2 +5V -- --
30 SA1 OSC -- --
31 SA0 0V -- --
32 0V 0V -- --

Rows C and D are not required on 8-bit modules. B10 and C19 are key locations.
Signal timing and function are as specified in ISA specification. Signal source/sink current differ from ISA values.

This information should be correct, but may be not. You can help us to improve this webpage!
You can confirm this document to be correct (be careful), or report an error in document (error may be described in the following webpage). Result of your submission will be used for calculating document status shown at the bottom of this page.
Related Links:
Pinouts.ru > Pinouts of different motherboard slots >  Pinout of PC/104 bus and layout of 146 pin PC/104 16 bit connector

Source(s): PC/104 v2.3 spec, PC/104 pinout, PC/104 Consortium, from Hardware Book
Document status: unknown
mark as erroneous!
mark as correct
0 report(s)
Click one of this links to change document status.
[Discuss at the forum] [Back to index] [Add new pinout]
[Report an error or update]
This information is maintained by pinouts.ru team and provided as a guideline only.
Efforts have been made to ensure it is correct, but it is the responsibility of the user
to verify the data is correct for their application.
71 hits since February 12, 2005