pinouts

Apple ATA connector

pinout (распиновка)

запомнить адрес в закладки

The internal hard disk has a 48-pin connector that carries both the ATA signals and the power for the drive.

разъем 48 pin Apple ATA
48 pin Apple ATA connector  at the Apple computer
The connector has the dimensions of a 50-pin connector, but with one row of pins removed. The remaining pins are in two groups: pins 1–44, which carry the signals and power, and pins 45–48, which are reserved.
Pin Name Dir Description
1 /RESET --> Reset
2 GND --- Ground
3 DD7 <-> Data 7
4 DD8 <-> Data 8
5 DD6 <-> Data 6
6 DD9 <-> Data 9
7 DD5 <-> Data 5
8 DD10 <-> Data 10
9 DD4 <-> Data 4
10 DD11 <-> Data 11
11 DD3 <-> Data 3
12 DD12 <-> Data 12
13 DD2 <-> Data 2
14 DD13 <-> Data 13
15 DD1 <-> Data 1
16 DD14 <-> Data 14
17 DD0 <-> Data 0
18 DD15 <-> Data 15
19 GND --- Ground
20 KEY - Key (Pin missing)
21 DMARQ ? DMA Request
22 GND --- Ground
23 /DIOW, /STOP --> Write Strobe
24 GND --- Ground
25 /DIOR, /HDMARDY, HSTROBE -->
26 GND --- Ground
27 IORDY, /DDMARDY, DSTROBE <-- I/O Ready,...
28 CSEL ?
29 /DMACK ? DMA Acknowledge
30 GND --- Ground
31 INTRQ <-- Interrupt Request
32 /IOCS16 ? obsolete, not used
33 /DA1 --> Address 1
34 /PDIAG, /CBLID ? Passed Diagnostics
35 /DA0 --> Address 0
36 /DA2 --> Address 2
37 /CS0 -->
38 /CS1 -->
39 /DASP -->
40 GND --- Ground
41 +5V LOGIC
42 +5V MOTOR
43 GND Ground
44 Reserved

/DA(0–2) Device address; used by the computer to select one of the registers in the ATA drive. For more information, see the descriptions of the CS0 and CS1 signals.

DD(0–15) Data bus; buffered from IOD(16–31) of the computer’s I/O bus. DD(0–15) are used to transfer 16-bit data to and from the drive buffer. DD(8–15) are used to transfer data to and from the internal registers of the drive, with DD(0–7) driven high when writing.

/CBLID The host checks this signal after Power On or hardware reset to detect whether an 80-conductor cable is present.

/CS0 Register select signal. It is asserted low to select the main task file registers. The task file registers indicate the command, the sector address, and the sector count.

/CS1 Register select signal. It is asserted low to select the additional control and status registers on the ATA drive.

CSEL Cable select; not available on the iBook.

/DASP Device active or slave present; not available on the iBook.

/DDMARDY Drive ready to receive Ultra DMA data.

/DIOR I/O data read strobe.

/DIOW I/O data write strobe.

/DMACK Used by the host to initiate a DMA transfer in response to DMARQ.

DSTROBE Strobe for Ultra DMA data transfers to host.

/HDMARDY Ultra DMA data ready.

HSTROBE Strobe for Ultra DMA data transfers from host.

IORDY I/O ready; when driven low by the drive, signals the CPU to insert wait states into the I/O read or write cycles.

/IOCS16 I/O channel select; not used on this computer (pulled low by 1 kilohm resistor).

DMARQ Asserted by the device when it is ready to transfer data to or from the host.

INTRQ Interrupt request. This active high signal is used to inform the computer that a data transfer is requested or that a command has terminated.

/PDIAG Asserted by device 1 to indicate to device 0 that it has completed the power-on diagnostics; not available on the iBook.

/RESET Hardware reset to the drive; an active low signal.

/STOP Stop request; an active low signal.

Key This pin is the key for the connector.

Эта информация должна быть правильной, но ошибки вполне возможны. Вы можете помочь!
Вы можете подтвердить правильность документа (только если действительно уверены), или сообщить об ошибке в документе (ошибка может быть описана далее по ссылке). Ваше мнение будет учтено при расчете статуса документа.
Pinouts.ru > Разъемы для подключения винчестеров >  Распиновка Apple ATA connector использующего разъем 48 pin Apple ATA

Источник(и): Apple iBook developer note
Статус документа: не подтвержденный
отметить как ошибочный!
отметить как правильный
0 отзыв(ов)
Щелкните по одной из ссылок для изменения статуса документа.
[Обсудить на форуме] [Назад к оглавлению] [Добавить распайку]
[Сообщить об ошибке или обновлении]
Maintained by pinouts.ru team
This information is provided as a guideline only.
Efforts have been made to ensure it is correct, but it is the responsibility of the user
to verify the data is correct for their application
43 hits since February 12, 2005