Pinouts of Connectors

Cisco EIA/TIA-530 DTE cable (DB60 to DB25) pinout

layout
schematic diagram

add this page to bookmarks

60 pin Cisco DB connector pin-out & layout
60 pin Cisco DB connector

60 Pin1

Signal

25 Pin

Signal
Direction
DTE DCE2
J1-11
J1-12
TxD/RxD+
TxD/RxD-
J2-2
J2-14
BA(A), TxD+
BA(B), TxD-
-
-
J1-28
J1-27
RxD/TxD+
RxD/TxD-
J2-3
J2-16
BB(A), RxD+
BB(B), RxD-
-
-
J1-9
J1-10
RTS/CTS+
RTS/CTS-
J2-4
J2-19
CA(A), RTS+
CA(B), RTS-
-
-
J1-1
J1-2
CTS/RTS+
CTS/RTS-
J2-5
J2-13
CB(A), CTS+
CB(B), CTS-
-
-
J1-3
J1-4
DSR/DTR+
DSR/DTR-
J2-6
J2-22
CC(A), DSR+
CC(B), DSR-
-
-
J1-46
J1-47
Shield_GND
MODE_2
J2-1
-
Shield
-
Shorted
J1-48
J1-49
GND
MODE_1
-
-
-
-
Shorted
J1-5
J1-6
DCD/DCD+
DCD/DCD-
J2-8
J2-10
CF(A), DCD+
CF(B), DCD-
-
-
J1-24
J1-23
TxC/RxC+
TxC/RxC-
J2-15
J2-12
DB(A), TxC+
DB(B), TxC-
-
-
J1-26
J1-25
RxC/TxCE+
RxC/TxCE-
J2-17
J2-9
DD(A), RxC+
DD(B), RxC-
-
-
J1-44
J1-45
LL/DCD
Circuit_GND
J2-18
J2-7
LL
Circuit_ GND
-
-
J1-7
J1-8
DTR/DSR+
DTR/DSR-
J2-20
J2-23
CD(A), DTR+
CD(B), DTR-
-
-
J1-13
J1-14
TxCE/TxC+
TxCE/TxC-
J2-24
J2-11
DA(A), TxCE+
DA(B), TxCE-
-
-

Arrows indicate signal direction: - indicates DTE to DCE, and - indicates DCE to DTE.

1 Any pin not referenced is not connected.
2 The EIA-530 interface cannot be operated in DCE mode. A DCE cable is not available for the EIA-530 interface.

This information should be correct, but may be not. You can help us to improve this webpage!
You can confirm this document to be correct (be careful), or report an error in document (error may be described in the following webpage). Result of your submission will be used for calculating document status shown at the bottom of this page.
25 pin Cisco DB connector pin-outs & layouts
25 pin Cisco DB connector
Pinouts.ru > Pinouts and schemes of serial ports cables >  Pinout of Cisco EIA/TIA-530 DTE cable (DB60 to DB25) and layout of 60 pin Cisco DB connector and 25 pin Cisco DB connector

Source(s): Cisco Systems, Inc.
Document status: unknown
mark as erroneous!
mark as correct
0 report(s)
Click one of this links to change document status.
[Discuss at the forum] [Back to index] [Add new pinout]
[Report an error or update]
This information is maintained by pinouts.ru team and provided as a guideline only.
Efforts have been made to ensure it is correct, but it is the responsibility of the user
to verify the data is correct for their application.
87 hits since February 12, 2005