Pinouts of Connectors

Wallaby and Himalaya PDA interface port pinout

layout
schematic diagram

add this page to bookmarks

Wallaby and Himalaya come with two connectors on the bottom. Also for MDA, XDA, Eurotel DataPhone.

22 pin MALE Himalaya special connector pin-out & layout
22 pin MALE Himalaya special connector  at the PDA (keypad up)
The large connector has pins for the USB port, serial port com1, power and audio (in and out). The connector is the same as on the 3800 or newer series iPaq, but the pinout is different. This means none of the iPaq peripherals will work.
The connector pinout
1 CAR_MIC_IN
2 GND / SENSE
3 CAR_AUDIO_R
4 CAR_AUDIO_L
5 ANALOG GND
6 RS232_DCD
7 RS232_CTS
8 RS232_TXD
9 RS232_RTS
10 RS232_RXD
11 RS232_DTR
12 NC
13 USB_VDD
14 UDC+
15 UDC-
16 GND
17 GND
18 GND
19 CAR_ON#
20 V_ADP
21 V_ADP
22 V_ADP

Notes:
CAR_ON# is connected to +6V/+5V on the car charger, it"s not connected in the cradle. +6V/+5V makes the phone go to speaker mode immediately when picked up or dialing. When this pin is connected to ground, the internal mike and speaker are turned off, and audio input is taken from the audio input pin on the connector, for use in real car kits.
Pin 2 GND / SENSE is not necessary. it seems that if it"s grounded, the phone hangs up when placed in a DIY Car-holder for example. - leave it unconnected.
Pin 5 ANALOG GND - connect this to your sound Input/output-GND (Speaker/Microphone) - do not connect this with the other GND"s - it makes a lot of noise on the analog input/outputs. Audio needs to be capacitively coupled in, any DC bias seems to inhibit audio.

If RS232_DCD is pulled to +6V/+5V, the device turns on and ActiveSync is started. The serial port powers down and needs to be reopened after the device goes in power-save mode.

USB power also wakes up the device and starts ActiveSync. UDC+ and UDC- are the USB data connections. One person reported measuring them the other way around.

Cable to plug into computer

This is the cable you need to talk to the Wallaby or Himalaya serially from a computer, such as is needed with our Manipulator program or for using ActiveSync through the serial port. Techies like us call it a "null-modem cable", O2 describes it as a "serial hotsync cable". Optionally, if you wish to be able to power/charge to XDA while using this cable, you could hook up a female connector that mates with the connector on your power adapter between Ground (pins 2,5,etc. on XDA) and pins 20,21 and 22 on the XDA. Make sure the center conductor on the power connector goes to pins 20,21 and 22.

Wallaby /
Himalaya
9-pin connector
(male)
2,5,16,17,18 5 (gnd)
6 (dcd) 4 (dtr)
7 (cts) 7 (rts)
8 (txd) 2 (rxd)
9 (rts) 8 (cts)
10 (rxd) 3 (txd)
11 (dtr) 6,1 (dsr, dcd)

Cable to plug into modem or GPS

This cable will connect to devices which come with a cable to plug into a PC serial port, such as a modem. If you are connecting to a device that only uses RX, TX and GND (such as many GPS receivers), you may only need the wires which connect to pins 2, 3 and 5 on the 9-pin serial connector. And you can, optionally, hook up a charging interface in the same way as described above.

Wallaby /
Himalaya
9-pin connector
(female)
2,5,16,17,18 5 (gnd)
6 (dcd) 1 (dcd)
7 (cts) 8 (cts)
8 (txd) 3 (txd)
9 (rts) 7 (rts)
10 (rxd) 2 (rxd)
11 (dtr) 4 (dtr)

Modifying iPaq accessories

Using the pinout of the XDA connector, you can now modify iPaq accessories to fit the Wallaby or Himalaya.

Wallaby /
Himalaya
iPaq
36xx or 37xx
iPaq
38xx or newer
2,5,16,17,18 (gnd) 4,10 10,15,22
6 (dcd) 9 6
(or 11, see below)
7 (cts) 5 13
8 (txd) 7 8
9 (rts) 6 12
10 (rxd) 8 7
11 (dtr) 3 9
14 (udc+) 11 19
15 (udc-) 12 21
20,21,22 (power) 1,2 1,2,3,4

This information should be correct, but may be not. You can help us to improve this webpage!
You can confirm this document to be correct (be careful), or report an error in document (error may be described in the following webpage). Result of your submission will be used for calculating document status shown at the bottom of this page.
Pinouts.ru > PDA, HandHeld computers connectors >  Pinout of Wallaby and Himalaya PDA interface port and layout of 22 pin MALE Himalaya special connector

Source(s): wiki.xda-developers.com
Document status: unknown
mark as erroneous!
mark as correct
0 report(s)
Click one of this links to change document status.
[Discuss at the forum] [Back to index] [Add new pinout]
[Report an error or update]
This information is maintained by pinouts.ru team and provided as a guideline only.
Efforts have been made to ensure it is correct, but it is the responsibility of the user
to verify the data is correct for their application.
160 hits since February 12, 2005